Sunday, 26 June 2011

3 Channel Spectrum Analyzer

This 3 channel 15 LED spectrum analyzer is the perfect addition to any audio amp project. It produces fantastic displays on three LED bars that can be individually adjusted for any particular frequency range. The circuit will take line level output from most any audio source, and operates on 12V DC. This means that it can even be run in a car.



Parts
R1                                            (1) 100K 1/4W Resistor
R2                                            (1) 820K 1/4W Resistor
R3, R14, R16, R18                    (4) 2.2 Meg 1/4W Resistor
R4, R5, R6                               (3) 22K Pot
R7,R8,R9,R25,R27 R29            (6)10K 1/4W Resistor
R10, R11, R12                         (3) 680 Ohm 1/4W Resistor
R13. R15, R17                         (3) 580K 1/4W Resistor
R19, R20, R21                         (3) 39K 1/4W Resistor
R22, R23, R24                         (3) 47K 1/4W Resistor
R26, R28, R30                         (3) 33 Ohm 1/4W Resistor
C1, C5, C6                               (3) 0.012uF Polystyrene Capacitor
C2, C9, C10, C11                     (4) 3.3uF Electrolytic Capacitor
C3, C4                                    (2)0.0022uF Polystyrene Capacitor
C7, C8                                    (2)47nF Polystyrene Capacitor
C12, C13, C14                        (3)0.47uF Electrolytic Capacitor
C15, C16, C17                        (3)22uF Electrolytic Capacitor
D1, D2, D3                             (3)1N4002 Silicon Diode
D4, D5, D6, D8, D8                 (5)Green LED
D10,D11,D12,D13,D14            (5)Amber LED
D16,D17,D18,D19,D20            (5)Red LED
U1                                         (1)LM3900 Quad Op Amp
U2, U3, U4                             (3)AN6884 Bar Graph IC
MISC                                     (1)Board, Wires, Sockets For ICs




Notes

  1. The circuit expects line level inputs. If you connect it to speaker level, you will have to readjust the circuit every time you change the volume.
  2. After the circuit is connected, apply power and signal. Now adjust the pots until the corresponding group of LEDs reacts.
  3. Thanks to Alterac for correcting some errors on the schematic that originally appeared on this page. Read all about it in the 3 Channel Spectrum Analyzer Project thread in the forum.

 source

Friday, 24 June 2011

Strobe Light

Disco anyone? Actually, this strobe serves a much more useful purpose then making it look cool when you dance in the dark. You can use it to view fast moving objects, look for craks in PC boards (hold the strobe on the trace side of the board and look from the component side), and it is a great attention getter in a store window.
Parts


R1            1        10 Meg, 1/4 Watt Resistor
D1, D2      2       1N4003 Silicon Diode or 1N4007
C1, C2      2       10uF 350V Capacitor
C3            1         0.1uF 400 Volt Mylar Capacitor
T1             1        4KV Trigger Transformer (see "Notes")
FT             1       Flash Tube (see "Notes")
L1             1        Neon Bulb
Q1             1        106 SCR
S1             1        115V 1A SPST Switch
MISC         1        Case, Wire, Line Cord


Notes
  1. This circuits is NOT isolated from ground. Use caution when operating without a case. A case is required for normal operation. Do not touch any part of the circuit with the case open or not installed.
  2. Most any diodes rated at greater then 250 volts at 1 amp can be used instead of the 1N4003's.

Thursday, 23 June 2011

Infa-Red Remote Control

I have received a number of emails requesting schematics for infa-red remotes. So here is one. This remote transmits a tone using an infa-red LED. This tone is decoded by the receiver. Since the receiver only switches when it "hears" the tone, there are no accidental activations.

Schematic For Transmitter

Schematic For Receiver

Parts




R1              1               22K 1/4W Resistor
R2              1               1 Meg 1/4W Resistor
R3              1               1K 1/4W Resistor
R4, R5        2               100K 1/4W Resistor
R6              1               50K Pot
C1, C2        2                0.01uF 16V Ceramic Disk Capacitor
C3              1               100pF 16V Ceramic Disk Capacitor
C4              1               0.047uF 16V Ceramic Disk Capacitor
C5              1               0.1uF 16V Ceramic Disk Capacitor
C6              1               3.3uF 16V Electrolytic Capacitor
C7              1               1.5uF 16V Electrolytic Capacitor
Q1              1               2N2222 NPN Silicon Transistor or 2N3904
Q2              1               2N2907 PNP Silicon Transistor
Q3              1               NPN Phototransistor
D1              1              1N914 Silicon Diode
IC1              1              LM308 Op Amp IC
IC2              1              LM567 Tone Decoder
LED1          1              Infa-Red LED
RELAY       1              6 Volt Relay
S1              1              SPST Push Button Switch
B1              1              3 Volt Battery or Two 1.5V batteries in series
MISC          1              Board, Sockets For ICs, Knob For R6, Battery Holder
RELAY       1              6 Volt Relay


Tuesday, 21 June 2011

FET Audio Mixer

This simple circuit mixes two or more channels into one channel (eg. stereo into mono). The circuit can mix as many or as few channels as you like and consumes very little power. The mixer is shown with two inputs, but you can add as many as you want by just duplicating the "sections" which are clearly visible on the schematic.
Parts
R1,R3            2               10k pot
R2,R4            2               100k
R5                 1               6.8k
C!,C2,C3        3              0.1uF capacitor
Q1                1               2N3819 junction fet
MISC            1               wire,shielded(metal)case,phono or other plug for ouput


Notes

  1. As many or as few channels as are required can be added to the mixer. Do this by just duplicating the input "sections" which are shown on the schematic.
  2. A shielded case is probably needed to reduce hum and help stop oscillations.
  3. The circuit can be powered by a single 9 volt battery.

Digital Volume Control

This digital volume control has no pot to wear out and introduces almost no noise in the circuit. Instead, the volume is controlled by pressing UP and DOWN buttons. This simple circuit would be a great touch to any home audio project.
Parts
C1                1           0.1uF ceramic disc capacitor
U1                1           DS1669 digital pot ic
S!,S2           2           momentary push button switch
MICS           1           board,wire,socket for u1


Notes

  1. S1 turns the volume up, S2 turns it down.
  2. The input signal should not fall below -0.2 volts.
  3. Using a dual polariity power supply (+-5V works fine) will cure most clipping problems. You will have to check the data sheet for the correct pins to connect your voltages.

Saturday, 18 June 2011

LASER Transmitter/Receiver

This set of two circuits from the basis for a very simple light wave transmitter. A LASER beam is modulated and then aimed at a receiver that demodulates the signal and then presents the information (voice, data, etc..). The whole thing is very easy to build and requires no specialized parts execpt for the LASER itself. LASERs are available from MWK Industries.

Schematic Of Transmitter


Schematic Of Receiver





Parts
C!,C2               2             0.1uF ceramic disc capacitor
C3                    1             100uF 25v electrolytic capacitor
R1                    1             100k ohm 1/4w resistor
R2                    1             1M ohm 1/4 resistor
R3                    1             10k pot
Q1                    1              NPN phototransistor
U1                    1              741 op amp
U2                    1              LM386 audio amp
SPKR1            1              8ohm speaker
T1                     1             8ohm:2k audio transformer
MISC                1             wire,board,knob for r3,laser tube and power supply


Note

  1. In the transmitter schematic, no ballast resistor is shown because most small LASER power supplies already have one built in. Yours may differ, and a resistor may be needed.
  2. The receiver should be kept away from bright lights. You may want to put a piece of wax paper in front of Q1 to keep the LASER from swamping it.
  3. In order to get any decent amount of modulation, you may need to drive T1 with more then a watt.
  4. The circuit can be made to transmit computer data with the use of two modem chips.